Firmware For 3D Printer

You can find the firmware for Eryone 3d printer at this section
User avatar
Eryone
Site Admin
Posts: 29
Joined: Wed May 08, 2019 6:50 pm

Firmware For 3D Printer

Post by Eryone » Sat May 11, 2019 11:46 am

Hi,guys!
All the firmware for Eryone 3D printer are here.
You can choose the firwmare then download it.
--------------------------------------------------------------------------
--------------------------------------------------------------------------
Note:
1. Enabled the z axis babystep
2. Added the config for bltouch or npn sensor
3. Enabled the LCD info
Updated time:2019/5/11
4. Enabled the mesh bed leveling feature
5. Enabled the individual axis homing menu
6. Enabled the LCD status menu
Updated time:2019/11/6
1. Fixed some errors.
Updated time:2019/11/11
1. Fixed some errors.
Updated time:2019/12/03
1. If you find your extruder won't work, please add the "M900 K0"
at the start code
Updated time:2019/12/27
1. Released the marlin 2.0.x firmware for thinker V2 board printer
2. Released the marlin 2.0.x firmware for thinker V1 board printer
3. Fixed the mesh bed leveling can't work with power loss recovery feature bug
4. Fixed the extruder manual move incorrect bug
Updated time:2020/3/3
For Thinker V2 Marlin 2.0.x Firmware
1. Tested the LJ12A3-4-Z/AX and LJ12A3-4-Z/BX inductive proximity switch
2. Added the config of the tested sensor
3. Fixed the pin definition of the 'pins_rambo.h' incorrect. Now we set it to '4' and it works.
Updated time:2020/3/17



Eryone Thinker S2.0/2.1/SE(Thinker V2 board) 3d Printer
Note:
This section is for our beta plan users.
If your printer is thinker then don't upload it. This firmware is for thinker V2 3d printer


-------------------------------------------------------------------------------------------------------------------
-------------------------2020.2.27 Updated-------------------------------------------------------------------
Firmware for thinker V2 (Included the config for bltouch and NPN sensor)
The board:
Thinker 2560V2.jpg
Thinker 2560V2.jpg (288.35 KiB) Viewed 5881 times



Marlin 2.0.x For Thinker V2
Note:
1. Tested movement,bltouch, NPN sensor, mesh bed leveling,
power loss recovery, and heating feature
2. If you find the bug please feedback then we can fix it at the first time
3. How to use the auto level sensor config:
1) Folder'2560Marlin2.0'>>>>>>'Marlin'>>>>'auto_level_config'
2) Copy the 'configruation.h' , 'configuration_adv.h' and 'Version.h'
3) Back to 'Marlin' folder and replace the old config
4) When the firmware uploaded, please use the "M502" and "M500" to reset the EEPROM of the printer.
Please refer to this video then upload it:

https://www.youtube.com/watch?v=b2D4I9Yxejw&t=13s

Update:
2020/03/17
Thinker V2_Marlin2.0_20200317.zip
(13.45 MiB) Downloaded 554 times
2020/03/03
Thinker V2 _Marlin2.0.zip
(13.14 MiB) Downloaded 214 times
By Robert and Tom
MD5: 3EC8422CFE74BA730A5A3D7B59051582



Old version(Marlin1.1.9)
Marlin_thinkerV2.zip
(3.52 MiB) Downloaded 281 times



Eryone Thinker/Thinker S1.0~1.2 3d Printer

Marlin 2.0.x For thinker V1(Thinker~ thinker S1.2)
Note:
1. Tested movement,bltouch, NPN sensor, mesh bed leveling,
power loss recovery, and heating feature
2. If you find the bug please feedback then we can fix it at the first time
3. How to use the auto level sensor config:
1) Folder'2560Marlin2.0'>>>>>>'Marlin'>>>>'auto_level_config'
2) Copy the 'configruation.h' , 'configuration_adv.h' and 'Version.h'
3) Back to 'Marlin' folder and replace the old config
4) When the firmware uploaded, please use the "M502" and "M500" to reset the EEPROM of the printer.
Marlin 2.0 thinker V1 beta3.zip
(13.2 MiB) Downloaded 234 times
MD5: 0FD572F1EC7B6BF3EC93E1882C27F757
Please refer to this video then upload it(This video is for thinker V2 but the steps are same):
https://www.youtube.com/watch?v=b2D4I9Yxejw&t=13s

1.Stock Firmware
Version(2019/11/11):
Thinker series1101-Marlin1.1.9.zip
(3.38 MiB) Downloaded 513 times
Version(2019/5/11):
Eryone thinker Marlin1.1.9.zip
(3.43 MiB) Downloaded 311 times



2.Firmware for Bltouch
Version(2019/11/11):
Thinker series1101-Marlin1.1.9 bltouch.zip
(3.38 MiB) Downloaded 343 times
Old version(2019/5/11):
Marlin for 3dtouch and bltouch.zip
(3.51 MiB) Downloaded 276 times
Guide+Stl of the bltouch on Thinker:
For BltouchV3.1 with thinker/thinkerS
Eryone thinker bltouchV3.1 plate.zip
(10.17 KiB) Downloaded 637 times
Guide:
https://youtu.be/fmzrUYbM1hQ
stl:
Bltouch GuideV1.2.zip
(988.66 KiB) Downloaded 375 times


3.Firmware for Npn sensor
New version(2019/11/11):
Thinker series1101-Marlin1.1.9 npn.zip
(3.38 MiB) Downloaded 147 times
Old version(2019/5/11):
Marlin_NPN.zip
(3.44 MiB) Downloaded 183 times
Guide of the npn sensor on Thinker:
NPN sensor Guide for thinker.zip
(1 MiB) Downloaded 219 times
Download the correct firmware then upload it.
Refer to this post then upload it to your printer
:
http://www.eryone.com/forum/viewtopic.p ... t=9&p=9#p9

clemfarfar
Posts: 18
Joined: Wed Dec 04, 2019 10:45 pm

Re: Firmware For 3D Printer

Post by clemfarfar » Wed Dec 04, 2019 10:47 pm

hello, have you planned a marlin 2.0 or 2.1?

User avatar
William
Site Admin
Posts: 111
Joined: Fri May 10, 2019 11:40 pm

Re: Firmware For 3D Printer

Post by William » Fri Dec 06, 2019 11:51 am

clemfarfar wrote:
Wed Dec 04, 2019 10:47 pm
hello, have you planned a marlin 2.0 or 2.1?
Hi, thanks for your suggest!
We've got the info of the official Marlin2.0 is released.
So we will try to update the firmware to Marlin2.0.
Because Marlin2.0 changed a lot in the framework then we need to do a lot test.
When we fixed the most bugs then we will release the beta version.
;)
## To be friendly and stay humble
- Pride and ignorance are eternal enemies
:)

clemfarfar
Posts: 18
Joined: Wed Dec 04, 2019 10:45 pm

Re: Firmware For 3D Printer

Post by clemfarfar » Sat Dec 07, 2019 2:00 am

thank's

be_st
Posts: 5
Joined: Thu Dec 12, 2019 12:09 am

Re: Firmware For 3D Printer

Post by be_st » Fri Dec 13, 2019 3:20 am

Hello,

so i have my new Thinker S 3D Printer. How can i check wich Version of Update i need?

Thanks Bernie
Eryone Thinker S

clemfarfar
Posts: 18
Joined: Wed Dec 04, 2019 10:45 pm

Re: Firmware For 3D Printer

Post by clemfarfar » Sat Dec 14, 2019 2:19 am

hello be_st

info print / info print ;) you check version ;) :lol: I speak little english :mrgreen:

be_st
Posts: 5
Joined: Thu Dec 12, 2019 12:09 am

Re: Firmware For 3D Printer

Post by be_st » Mon Dec 16, 2019 10:50 pm

Thank You Clemfarfar!

Do You know can i use the 2.0 Version for my printer Thinker S ?

Best Greetings from Germany

clemfarfar wrote:
Sat Dec 14, 2019 2:19 am
hello be_st

info print / info print ;) you check version ;) :lol: I speak little english :mrgreen:
Eryone Thinker S

clemfarfar
Posts: 18
Joined: Wed Dec 04, 2019 10:45 pm

Re: Firmware For 3D Printer

Post by clemfarfar » Wed Dec 18, 2019 3:32 am

not the forum V2, it does not work on our 3d printer, I tested and no screen they will release a 2.0 marlin but it needs to fix the bugs.

tala16
Posts: 1
Joined: Fri Apr 03, 2020 1:23 pm

Re: Firmware For 3D Printer

Post by tala16 » Fri Apr 03, 2020 1:27 pm

Hello everyone. I have a Thinker se, the firmware v 2.0 is fine for my printer? Thanks

Beorhted
Posts: 3
Joined: Sun Apr 12, 2020 10:59 pm

Re: Firmware For 3D Printer

Post by Beorhted » Sun Apr 12, 2020 11:01 pm

Hi, I have the first thinker model, which marlin do I use? the 1101 mounts but at an inch from the plate the extruder stops. what do I do? thank you

Post Reply