[solved] movement in x goes crazy

When you find your machine has problems. You can have a look at this section
Post Reply
clemfarfar
Posts: 18
Joined: Wed Dec 04, 2019 10:45 pm

[solved] movement in x goes crazy

Post by clemfarfar » Fri Dec 27, 2019 2:51 am

Bonjour,

en français :
j'ai monté un bltouch qui ne marche pas surement un défaut de celui ci , mais depuis j'ai mon axe X quand je lui demande 10mm bouge d'au moins le triples , je suis revenu en firmware d'origine sans bl touch !
english :

I mounted a bltouch which does not work surely a defect of this one, but since I have my X axis when I ask it 10mm moves at least the triples, I returned to the original firmware without bl touch!

https://www.youtube.com/watch?v=G88aI8r_aqE
20191226_200242[1].jpg
20191226_200242[1].jpg (1.57 MiB) Viewed 298 times
20191226_200547[1].jpg
20191226_200547[1].jpg (1.33 MiB) Viewed 298 times

clemfarfar
Posts: 18
Joined: Wed Dec 04, 2019 10:45 pm

Re: "résolue/ resolved" mouvement X devient fou /movement in x goes crazy

Post by clemfarfar » Fri Dec 27, 2019 5:37 am

french :
Bon bas , c'est le drive qui a cramé :x !

english :

Good down, it's the drive that burned: x!

User avatar
Eryone
Site Admin
Posts: 29
Joined: Wed May 08, 2019 6:50 pm

Re: [solved] movement in x goes crazy

Post by Eryone » Mon Dec 30, 2019 9:57 am

Good job!
:lol:
Thanks for your sharing~

clemfarfar
Posts: 18
Joined: Wed Dec 04, 2019 10:45 pm

Re: [solved] movement in x goes crazy

Post by clemfarfar » Mon Dec 30, 2019 6:23 pm

I still had a problem yesterday with the drives but this time I disassembled for the reglers, xy 1v, Z 1.05 E 0.95 to 1 v: x thank you to tom who answered me on facebook this morning;)


bltouch ok , axe ok :D :lol:

User avatar
kaktus
Site Admin
Posts: 11
Joined: Sat Jun 01, 2019 3:58 pm

Re: [solved] movement in x goes crazy

Post by kaktus » Thu Jan 02, 2020 10:59 pm

Hello.
:mrgreen:

It's good to give a solution here.
A lot of people can use it.

clemfarfar
Posts: 18
Joined: Wed Dec 04, 2019 10:45 pm

Re: [solved] movement in x goes crazy

Post by clemfarfar » Fri Jan 03, 2020 4:50 am

Hi, the stock vref of TMC2208 :
X/Y is 1.0V
Z-axis is 1.05V
Extruder is 0.95V~1.0V


thanks tom :)

clemfarfar
Posts: 18
Joined: Wed Dec 04, 2019 10:45 pm

Re: [solved] movement in x goes crazy

Post by clemfarfar » Sun Jan 05, 2020 8:00 am

Hello after recalculation and help from the French-speaking facebook community, the vref would be around 1.06V for the XYZ Axis and 1.19V for the E if I used the extruder motor which would be 1.68A on the E and 1.5A on the XYZ axes


XYZ VREF 1.06V motor 1.5A
E VREF 1.19V motor 1.68A

Post Reply