All the firmware for Eryone 3D printer are here.
You can choose the firwmare then download it.
The new firmware for the thinker V2, pls check this link(2020/7/23):
https://github.com/Eryone/mega2560/tree ... mware-Beta
--------------------------------------------------------------------------
--------------------------------------------------------------------------
Note:
1. Enabled the z axis babystep
2. Added the config for bltouch or npn sensor
3. Enabled the LCD info
Updated time:2019/5/11
4. Enabled the mesh bed leveling feature
5. Enabled the individual axis homing menu
6. Enabled the LCD status menu
Updated time:2019/11/6
1. Fixed some errors.
Updated time:2019/11/11
1. Fixed some errors.
Updated time:2019/12/03
1. If you find your extruder won't work, please add the "M900 K0"
at the start code
Updated time:2019/12/27
1. Released the marlin 2.0.x firmware for thinker V2 board printer
2. Released the marlin 2.0.x firmware for thinker V1 board printer
3. Fixed the mesh bed leveling can't work with power loss recovery feature bug
4. Fixed the extruder manual move incorrect bug
Updated time:2020/3/3
For Thinker V2 Marlin 2.0.x Firmware
1. Tested the LJ12A3-4-Z/AX and LJ12A3-4-Z/BX inductive proximity switch
2. Added the config of the tested sensor
3. Fixed the pin definition of the 'pins_rambo.h' incorrect. Now we set it to '4' and it works.
Updated time:2020/3/17
Eryone Thinker S2.0/2.1/SE(Thinker V2 board) 3d Printer
Note:
This section is for our beta plan users.
If your printer is thinker then don't upload it. This firmware is for thinker V2 3d printer
-------------------------------------------------------------------------------------------------------------------
-------------------------2020.2.27 Updated-------------------------------------------------------------------
Firmware for thinker V2 (Included the config for bltouch and NPN sensor)
The board:
- Thinker 2560V2.jpg (288.35 KiB) Viewed 6874 times
Marlin 2.0.x For Thinker V2
Note:
1. Tested movement,bltouch, NPN sensor, mesh bed leveling,
power loss recovery, and heating feature
2. If you find the bug please feedback then we can fix it at the first time
3. How to use the auto level sensor config:
1) Folder'2560Marlin2.0'>>>>>>'Marlin'>>>>'auto_level_config'
2) Copy the 'configruation.h' , 'configuration_adv.h' and 'Version.h'
3) Back to 'Marlin' folder and replace the old config
4) When the firmware uploaded, please use the "M502" and "M500" to reset the EEPROM of the printer.
Please refer to this video then upload it:
https://www.youtube.com/watch?v=b2D4I9Yxejw&t=13s
Update:
2020/03/17 2020/03/03 By Robert and Tom
MD5: 3EC8422CFE74BA730A5A3D7B59051582
Old version(Marlin1.1.9)
Eryone Thinker/Thinker S1.0~1.2 3d Printer
Marlin 2.0.x For thinker V1(Thinker~ thinker S1.2)
Note:
1. Tested movement,bltouch, NPN sensor, mesh bed leveling,
power loss recovery, and heating feature
2. If you find the bug please feedback then we can fix it at the first time
3. How to use the auto level sensor config:
1) Folder'2560Marlin2.0'>>>>>>'Marlin'>>>>'auto_level_config'
2) Copy the 'configruation.h' , 'configuration_adv.h' and 'Version.h'
3) Back to 'Marlin' folder and replace the old config
4) When the firmware uploaded, please use the "M502" and "M500" to reset the EEPROM of the printer. MD5: 0FD572F1EC7B6BF3EC93E1882C27F757
Please refer to this video then upload it(This video is for thinker V2 but the steps are same):
https://www.youtube.com/watch?v=b2D4I9Yxejw&t=13s
1.Stock Firmware
Version(2019/11/11): Version(2019/5/11):
2.Firmware for Bltouch
Version(2019/11/11): Old version(2019/5/11): Guide+Stl of the bltouch on Thinker:
For BltouchV3.1 with thinker/thinkerS Guide:
https://youtu.be/fmzrUYbM1hQ
stl:
3.Firmware for Npn sensor
New version(2019/11/11): Old version(2019/5/11): Guide of the npn sensor on Thinker: Download the correct firmware then upload it.
Refer to this post then upload it to your printer:
http://www.eryone.com/forum/viewtopic.p ... t=9&p=9#p9
I speak little english 