How to upload the firmware to your Printer

You can find the firmware for Eryone 3d printer at this section
Post Reply
User avatar
William
Site Admin
Posts: 130
Joined: Fri May 10, 2019 11:40 pm

How to upload the firmware to your Printer

Post by William » Sat May 11, 2019 3:52 pm

Hi,guys!
Here are the step by step guide of how to upload the firmware to your printer
1.Download the Arduino IDE and install it
The Arduino IDE offical website:
https://www.arduino.cc/en/Main/Software

2. If you are first using it,you need to download it from here(If you are not the first time using it then skip this step and see the step of 3):
Arduino_1.png
Arduino_1.png (72.67 KiB) Viewed 6164 times
Open the Arduino add the “U8glib“” to your library
Arduino_2.png
Arduino_2.png (126.84 KiB) Viewed 6164 times
Arduino_3.png
Arduino_3.png (37.42 KiB) Viewed 6164 times
3.1)Choose the correct board type and processor
Arduino_4.png
Arduino_4.png (75.03 KiB) Viewed 6164 times
2)Plug the USB cable to your PC/laptap
If you haven’t install the usb drives for your printer.You can refern to this link:
https://sparks.gogo.co.nz/ch340.html
3)Choose the correct COM port
Arduino_5.png
Arduino_5.png (71.33 KiB) Viewed 6164 times
4)Open the firmware and upload it to your printer
Arduino_6.png
Arduino_6.png (65.74 KiB) Viewed 6164 times
“File”>”Open”>“Marlin-BLTouch”>”Marlin”>”Marlin.ino”Click upload button
Arduino_7.png
Arduino_7.png (36.04 KiB) Viewed 6164 times
4.When Arduino IDE shows Done uploading you can remove the cables of USB off
Done

---------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------
If your printer motherboard is thinker V2 then you can refer to this video
then upload it

https://www.youtube.com/watch?v=RXN5-CvM_A4

Updated:2020/3/2
## To be friendly and stay humble
- Pride and ignorance are eternal enemies
:)

zas
Posts: 1
Joined: Sun Sep 13, 2020 10:50 pm

Re: How to upload the firmware to your Printer

Post by zas » Sun Sep 13, 2020 10:59 pm

Hi,

I'm trying to upgrade my recently bought Eryone Thinker SE from 1.1.9 to 2.x with BL touch, I tried everything, using Arduino IDE 1.8.13 on linux or windows, firmware compiles without errors but I always get timeout errors when trying to upload the firmware to the 3D printer:

avrdude: stk500v2_ReceiveMessage(): timeout

So far, I couldn't upgrade firmware because of this error, I wonder if I got a defective ATMEL MEGA 2560.

Anyone got similar issue?
What should I check?

User avatar
William
Site Admin
Posts: 130
Joined: Fri May 10, 2019 11:40 pm

Re: How to upload the firmware to your Printer

Post by William » Mon Sep 14, 2020 4:56 pm

zas wrote:
Sun Sep 13, 2020 10:59 pm
Hi,

I'm trying to upgrade my recently bought Eryone Thinker SE from 1.1.9 to 2.x with BL touch, I tried everything, using Arduino IDE 1.8.13 on linux or windows, firmware compiles without errors but I always get timeout errors when trying to upload the firmware to the 3D printer:

avrdude: stk500v2_ReceiveMessage(): timeout

So far, I couldn't upgrade firmware because of this error, I wonder if I got a defective ATMEL MEGA 2560.

Anyone got similar issue?
What should I check?
Hi, you can refer to this post at first. I think this post can help to sort out it:
viewtopic.php?f=9&t=308
:)
## To be friendly and stay humble
- Pride and ignorance are eternal enemies
:)

Post Reply