Thinker S V1.2 BLtouch Firmware?

Post Reply
Domhol26
Posts: 8
Joined: Mon Jan 06, 2020 12:45 am
Location: Germany

Thinker S V1.2 BLtouch Firmware?

Post by Domhol26 » Mon Jan 06, 2020 2:50 am

Hi folks,
I can't get the BLtouch V3.1 sensor to work on my Thinker S V1.2.
The manufacturer is ANTCLABS.
Which firmware should I use?

greeting
Dominic

User avatar
William
Site Admin
Posts: 130
Joined: Fri May 10, 2019 11:40 pm

Re: Thinker S V1.2 BLtouch Firmware?

Post by William » Mon Jan 06, 2020 9:07 pm

Hi,
Maybe you can try the firmware of mines.
You need to check the readme.txt then you can get more info./
Good luck
Firmware-1.png
Firmware-1.png (88.07 KiB) Viewed 4935 times
Firmware-2.png
Firmware-2.png (69.8 KiB) Viewed 4935 times
Eryone Thinker Serise_BL.zip
(1.37 MiB) Downloaded 191 times
## To be friendly and stay humble
- Pride and ignorance are eternal enemies
:)

clemfarfar
Posts: 18
Joined: Wed Dec 04, 2019 10:45 pm

Re: Thinker S V1.2 BLtouch Firmware?

Post by clemfarfar » Tue Jan 07, 2020 1:47 am

hi dom, you can take this one it works on my eryone with the bltouch 3.1
it's version 11/11/19
https://www.eryone.com/forum/download/file.php?id=134

User avatar
William
Site Admin
Posts: 130
Joined: Fri May 10, 2019 11:40 pm

Re: Thinker S V1.2 BLtouch Firmware?

Post by William » Tue Jan 07, 2020 3:38 pm

clemfarfar wrote:
Tue Jan 07, 2020 1:47 am
hi dom, you can take this one it works on my eryone with the bltouch 3.1
it's version 11/11/19
https://www.eryone.com/forum/download/file.php?id=134
:lol: That's a good news~
It seems your printer uses the YMAX port as the signal pin of the bltouch
## To be friendly and stay humble
- Pride and ignorance are eternal enemies
:)

Domhol26
Posts: 8
Joined: Mon Jan 06, 2020 12:45 am
Location: Germany

Re: Thinker S V1.2 BLtouch Firmware?

Post by Domhol26 » Tue Jan 14, 2020 9:12 pm

Hello everyone,
I checked the wiring, so far it's ok.
I noticed that another version of the mainboard is apparently installed in my printer. I don't have a YMAX connector on the board.
See https://www.eryone.com/forum/viewtopic.php?f=17&t=19 .
Can it be that my printer already has the board version V1.2?

greeting
DomHol26

Domhol26
Posts: 8
Joined: Mon Jan 06, 2020 12:45 am
Location: Germany

Re: Thinker S V1.2 BLtouch Firmware?

Post by Domhol26 » Fri Jan 17, 2020 6:36 am

Thanks clemfarfar,
with the "old" version the bltouch works fine.
But the extruder is now on strike, filament is no longer being conveyed during printing.
What can that be now?
Any ideas?
clemfarfar wrote:
Tue Jan 07, 2020 1:47 am
hi dom, you can take this one it works on my eryone with the bltouch 3.1
it's version 11/11/19
https://www.eryone.com/forum/download/file.php?id=134

Greetings
DomHol26

Domhol26
Posts: 8
Joined: Mon Jan 06, 2020 12:45 am
Location: Germany

Re: Thinker S V1.2 BLtouch Firmware?

Post by Domhol26 » Fri Jan 17, 2020 7:49 am

update:
When I use the filament change function,
the ejection runs at normal speed,
but the feeding is very slow and stops even after a short time. I can still push in ~ 10cm manually
Can it have anything to do with the stepper driver?

I checkt the Boad Rev with the LCD, so it is 1.0.

Good night from Germany:-)

Domhol26
Posts: 8
Joined: Mon Jan 06, 2020 12:45 am
Location: Germany

Re: Thinker S V1.2 BLtouch Firmware?

Post by Domhol26 » Wed Jan 22, 2020 4:34 am

Hello everybody,
the problem with the extruder is solved. :D
I had read in the Frimware section that if you had problems with the extruder
you still had to insert the code "M900 K0" in the slicer as the start code.
Many thanks to the German Facebook group Eryone Germany for support.
Finally, the only question that remains is why is a mainboard with a different layout installed in my printer?

greeting
DomHol26

Post Reply