[Upgrade] Creality ender3 printer with 32bit board

Post Reply
User avatar
Eryone
Site Admin
Posts: 29
Joined: Wed May 08, 2019 6:50 pm

[Upgrade] Creality ender3 printer with 32bit board

Post by Eryone » Thu May 30, 2019 9:12 pm

Hi, guys!
Today I will show you how to upgrade your Ender3 8bit board to more powerful board:
Eryone 32bit motherboard!

The introduce of this board:
https://hackaday.com/2019/05/10/a-32-bi ... d-printer/

Here we go!
Here are 2 sections of it: Wiring and Firmware
1.Wiring ender3 printer
Ender1.jpg
Ender1.jpg (58.24 KiB) Viewed 1275 times
Ender2.jpg
Ender2.jpg (77.47 KiB) Viewed 1275 times
Like the following images: You can put all the wires direct to board’s connector,except the endstop wires . Be careful, there are three pins towards the outside of the board(3.3v/GND/IN),that is different from the ender3’s, so you need to reversing the wires to the correct connector pins. make sure the wires correspond with the image bellow.
Ender3.jpg
Ender3.jpg (83.52 KiB) Viewed 1275 times
Ender4.jpg
Ender4.jpg (258.81 KiB) Viewed 1275 times
Ender5.jpg
Ender5.jpg (74.29 KiB) Viewed 1275 times
2. Firmware change, compile, upload:
You need to read “How to configure edit compile upload firmware” before you want to change the firmware, Some pins and endstop direction are different with the default value,you can just replace the 2 source files(Configuration.h,pins_ERYONE_STM32F103.h ) with the file in folder machines\ender3(you can download it from GitHub) .
Link:
https://github.com/Eryone/STM32

Configuration.h

Code: Select all

#define X_MIN_ENDSTOP_INVERTING false//true//false // set to true to invert the logic of the endstop. 
#define Y_MIN_ENDSTOP_INVERTING false//true//false // set to true to invert the logic of the endstop. 
#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. 

// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. 
#define INVERT_X_DIR true//false//true 
#define INVERT_Y_DIR true//false 
#define INVERT_Z_DIR false//true 

pins_ERYONE_STM32F103.h

Code: Select all

#define Z_MIN_PIN 0xE4// 0xB8//0xE1 
#define FAN3_PIN 0xD1//0xA0 

HmBeerBrewer
Posts: 2
Joined: Tue May 14, 2019 9:12 pm

Re: [Upgrade] Creality ender3 printer with 32bit board

Post by HmBeerBrewer » Fri May 31, 2019 5:50 pm

Looks like a very nice board. WIll future Eryone printers start using it as the default board once it becomes generally available.?

User avatar
Eryone
Site Admin
Posts: 29
Joined: Wed May 08, 2019 6:50 pm

Re: [Upgrade] Creality ender3 printer with 32bit board

Post by Eryone » Mon Jun 03, 2019 10:35 am

HmBeerBrewer wrote:
Fri May 31, 2019 5:50 pm
Looks like a very nice board. WIll future Eryone printers start using it as the default board once it becomes generally available.?
You are correct.We plan to use it at our next version printer. ;)

stormz85
Site Admin
Posts: 2
Joined: Tue Jun 11, 2019 8:10 pm

Re: [Upgrade] Creality ender3 printer with 32bit board

Post by stormz85 » Wed Jun 12, 2019 3:43 am

What about the users who has already the Eryone Thinker ? with the 1st board ?
can we except a price for them ?

User avatar
Eryone
Site Admin
Posts: 29
Joined: Wed May 08, 2019 6:50 pm

Re: [Upgrade] Creality ender3 printer with 32bit board

Post by Eryone » Wed Jun 12, 2019 6:05 pm

stormz85 wrote:
Wed Jun 12, 2019 3:43 am
What about the users who has already the Eryone Thinker ? with the 1st board ?
can we except a price for them ?
We will prepare it then release the price of this board at the announcement section
;)

Post Reply