Search found 10 matches

by Domhol26
Wed Oct 07, 2020 5:22 pm
Forum: Feedback
Topic: New heated Bed Thinker S
Replies: 2
Views: 589

Re: New heated Bed Thinker S

Hello William
many thanks for your response.
I'm from Germany.
It's not available here at amazon.

greeting
DomHol26
by Domhol26
Thu Oct 01, 2020 3:27 pm
Forum: Feedback
Topic: New heated Bed Thinker S
Replies: 2
Views: 589

New heated Bed Thinker S

Hello everybody,
I need a new heated bed for my Thinker S because the old one is unfortunately damaged.
When will "Eryone Maflex Magnetic Flexible Heated Bed with Sticker310 * 310mm Transparent PEI" be available again?

greeting
DomHol26
by Domhol26
Wed Feb 19, 2020 2:51 pm
Forum: Frequently Asked Questions
Topic: Stepper Motor
Replies: 2
Views: 4023

Re: Stepper Motor

Good Morning from Germany,

i had the same problem.
Please read my post:
https://www.eryone.com/forum/viewtopic. ... t=204#p380
You have to add

Code: Select all

M900 K0
in the startcode of your slicer.

Greetings

DomHol
by Domhol26
Thu Feb 13, 2020 2:44 pm
Forum: Frequently Asked Questions
Topic: BLTOUCH doesn't work
Replies: 2
Views: 3769

Re: BLTOUCH doesn't work

Good morning from Germany, I had the same problem with the Thinker S V1.2. here the forum contribution: https://www.eryone.com/forum/viewtopic.php?f=28&t=204 There you will find clemfafar's answer. hi dom, you can take this one it works on my eryone with the bltouch 3.1 it's version 11/11/19 https:/...
by Domhol26
Wed Jan 22, 2020 4:34 am
Forum: 3D Printer
Topic: Thinker S V1.2 BLtouch Firmware?
Replies: 7
Views: 6271

Re: Thinker S V1.2 BLtouch Firmware?

Hello everybody, the problem with the extruder is solved. :D I had read in the Frimware section that if you had problems with the extruder you still had to insert the code "M900 K0" in the slicer as the start code. Many thanks to the German Facebook group Eryone Germany for support. Finally, the onl...
by Domhol26
Fri Jan 17, 2020 7:49 am
Forum: 3D Printer
Topic: Thinker S V1.2 BLtouch Firmware?
Replies: 7
Views: 6271

Re: Thinker S V1.2 BLtouch Firmware?

update: When I use the filament change function, the ejection runs at normal speed, but the feeding is very slow and stops even after a short time. I can still push in ~ 10cm manually Can it have anything to do with the stepper driver? I checkt the Boad Rev with the LCD, so it is 1.0. Good night fro...
by Domhol26
Fri Jan 17, 2020 6:36 am
Forum: 3D Printer
Topic: Thinker S V1.2 BLtouch Firmware?
Replies: 7
Views: 6271

Re: Thinker S V1.2 BLtouch Firmware?

Thanks clemfarfar, with the "old" version the bltouch works fine. But the extruder is now on strike, filament is no longer being conveyed during printing. What can that be now? Any ideas? hi dom, you can take this one it works on my eryone with the bltouch 3.1 it's version 11/11/19 https://www.eryon...
by Domhol26
Tue Jan 14, 2020 9:12 pm
Forum: 3D Printer
Topic: Thinker S V1.2 BLtouch Firmware?
Replies: 7
Views: 6271

Re: Thinker S V1.2 BLtouch Firmware?

Hello everyone, I checked the wiring, so far it's ok. I noticed that another version of the mainboard is apparently installed in my printer. I don't have a YMAX connector on the board. See https://www.eryone.com/forum/viewtopic.php?f=17&t=19 . Can it be that my printer already has the board version ...
by Domhol26
Mon Jan 06, 2020 2:50 am
Forum: 3D Printer
Topic: Thinker S V1.2 BLtouch Firmware?
Replies: 7
Views: 6271

Thinker S V1.2 BLtouch Firmware?

Hi folks,
I can't get the BLtouch V3.1 sensor to work on my Thinker S V1.2.
The manufacturer is ANTCLABS.
Which firmware should I use?

greeting
Dominic
by Domhol26
Mon Jan 06, 2020 12:49 am
Forum: USERS' CORNER
Topic: I am Dominic
Replies: 1
Views: 2941

I am Dominic

Hello from Germany,

I started the year 2020 with a new Thinker S 3D Printer. The late xmas gift ;-)

Greeting

Dominic